Looking for Raspberry PI applications for article
By Curt Wuollet on 23 August, 2019 - 9:58 am
Hi Jeremy I have about 40 of them deployed on the door finishing plant floor. Most are involved...
By Mark / Automated Solutions on 22 August, 2019 - 12:26 pm
Hey Jeremy, I just wanted to let you know that Automated Solutions recently released a...
Help! Citect function Variable 1 = Variable 2
After general overhaul, when turbine restarts it displays a GG IDEL FAULT _ H fault
Inventory of Control Instruments
Want to make an inventory of all measurement instruments and actuators at my plant. Need your advice
GE Gas Turbine Frame 6 Manual
Looking for GE gas turbine frame 6 manual
By Kuldeep on 11 August, 2019 - 10:14 pm
Sir, In our power plant 30mw GE frame 6 duel fuel (gas and distillate) Co generation gas turbine...
GT Driving Centrifugal Compressor
GT drives Centrifugal compressor, any possibility without running the GT the reverse rotation can be happen from load compressor side to turbine ?
By shahabas on 16 August, 2019 - 8:11 am
The machine model: aeroderivative GT PGT25+G4 (dual shaft) GE turbine +gearbox +BCL806 compressor ...
SRV GCV Drawings for Plug/Seat/Gasket
SRV GCV replacement procedure
t3.5 Between Transmit Frame in Modbus
How to use the t3.5 interval properly during master/slave communication
What output should I expect in this circuit?
I have to find the correct value of output voltage for a simple OP07 circuit having a constant dc input
Old ABB Advant MOD 300 800xA systems
Looking to get addition info
Modbus Data/Communication Issue
Posted by D. Wubben on 3 July, 2019 - 2:05 pm
Modbus communication gimbal locks and values usually are all zeros.
By Deanna Wubben on 8 August, 2019 - 3:06 pm
The system that the values are read from has good values when I export the file. I then have to...
Triconex Tristation Serial Cable
Triconex Tristation serial cable pinout
By Mark on 8 August, 2019 - 12:13 am
Hello, To finish off the thread. I was able to use the same cable pinout as an Allen Bradley...
By Mark on 5 August, 2019 - 8:46 am
Thanks for the response. Same verbiage. That cable is for MODBUS. >It looks like you have...
By Mark on 4 August, 2019 - 1:30 pm
Thanks for the response. It is for the base plate on a Trident. I tried that pin out, a standard...
Condensate Pot for pressure transmitter installation.
ModbusPoll Excel to email
Generator Hydrogen Cooling System
hydrogen cooling system for GE frame6
RS485 to TCP/IP Converter
Can TCP/IP converter act as master controller for slave process controllers?
Checking Ripple Voltage AC and DC Voltage to MKV
Posted by PowerIsland on 25 July, 2019 - 2:17 am
How to check Ripple of AC (110 V AC) over (125) DC voltage in Mark V power supply
By Power Island on 26 July, 2019 - 6:12 am
Dear CSA, I would like to say "Thanks" for your quick and detailed reply and giving...
Starting Logic of Auxiliary Motors of Gas Turbine
Logic of auxiliary motors of gas turbine during starting and shutdown
By gustavo_marcelo on 24 July, 2019 - 7:53 pm
Hi, Since we are discussing the Start of Motor, I have one question. Why do we named the lube...
Setting up Modbus TCP Network
Modbus TCP communication got slower when number of slave increases.
[Survey] Smart Manufacturing Technology and Security
Personal research on the security awareness of smart manufacturing technology.
Connecting a Mouse to Monitouch HMI
Problems connecting a Mouse to a Monitouch HMI
MARK VI Trip History File
How can I get the TRIPLOG (TRIP HISTORY) file?
Maximum Axial Thrust Load in GE frame 9E
What is the maximum axial load that GE Frame 9E gas turbine thrust bearing can withstand?
Historian on HMI Mark V Not Working
Historical alarm and event report in HMI Mark V is Empty